Why the watch lasts longer than the work
The first rule of fire work is that a fire can smoulder for a long time after the crew has finished cutting or welding. In a print shop this matters especially, because solvents, paints and vapours are nearby and can ignite with a delay once the heat source is switched off. That is why particularly hazardous work, meaning hot work, work at height and work in confined spaces, requires a knowledge check, approval by an internal user of the plant and, for fire work, supervision after completion.
The system leaves no room for discretion over the watch. For hot work it enforces monitoring after 1 hour and after 4 hours in sequence, and closing is blocked until at least 3 hours of supervision have passed. The maintenance manager therefore does not have to watch the clock, because the permit cannot be closed earlier.
How to plan the watch next to the solvent store
The watch plan starts before the work, not after it. The manager decides who will be the observer, where they will stand and when their shift ends, because the 3 hours of watch after work in a print shop often fall during the shift handover. An observer who leaves at six cannot leave the job to someone who does not know the place.
It is also worth planning what happens to the solvent store in the meantime. In most plants, traffic in the store is stopped and new deliveries are postponed until the permit is closed. This condition is written into the description of the permit, so that it does not depend on memory.
Who can be the observer
The observer should be a person authorised to take the first response and with access to a fire extinguisher, preferably from a different crew than the one doing the work. This way the watch does not depend on the same person who was busy with welding, and does not end together with their shift.
How to arrange the first and the fourth hour
Both monitoring rounds, after 1 hour and after 4 hours, are mandatory and the system enforces them in sequence. Good practice: at the first round, check the work area and its surroundings for embers and smoke; at the second, also check the spaces under and behind the work site, where fire could hide.
Timeline of the watch after hot work
Documentation of the watch for an audit
The permit in the system is evidence that the contractor knew the hazards, that their knowledge was checked, that an internal user approved it and that the watch after the work lasted the required time. For a plant audited by a supplier or an insurer, this is the complete set in one place, without collecting slips of paper from different people.
Before work, the contractor sees the catalogue of hazards assigned to the job, and hazards can be edited in the 3D map editor for the given building level. It is therefore worth assigning the fire hazard to the level on which the solvent store is located, so that it is visible to every crew that receives a permit near it.
Typical mistakes in hot work
The most common mistake is planning the watch at the end of the shift. Three hours after the work ends at 13:00 is 16:00, and in many plants the maintenance crew finishes the day at 15:00. The system will not let the permit be closed before the watch ends, but it does not say who should be looking at the place.
The second mistake is treating the blocked closing as a system failure. The block is deliberate. Instead of asking about a fault, it is worth asking who is watching the work site during that time.
- The observer is appointed before the work, not after it.
- The change of observer is recorded in the description of the permit.
- Traffic in the solvent store is stopped for the duration of the watch.
- The first and second monitoring rounds are done on site, not from the office.
What stays with the plant
The system supports meeting the requirement and provides audit evidence, but the decision to admit hot work stays with the plant's manager. InnerWeb is a software producer and does not assess explosion hazard zones; that assessment is carried out by an authorised person on the plant's side, and beacons with ATEX design for zones 2 and 22 are selected according to its result.
Checklist
Video
Frequently asked questions
Can a hot work permit be closed before 3 hours have passed?
No. The system blocks closing until at least 3 hours of supervision after the work have passed.
Are the monitoring rounds after 1 and 4 hours optional?
No. The system enforces them in sequence for hot work.
Who approves particularly hazardous work?
It is approved by an internal user of the plant after checking the contractor's knowledge.
Let us set up the watch after hot work
We will show a work permit for hot work with the closing block and monitoring after 1 and 4 hours on a sample plant.
Let's talk