InnerWeb
Skip to main content

BLE wristband verification before entering a critical site

A BLE wristband is checked before entry to an energy plant the same way as any device that transmits a signal on a critical site: first the origin and firmware, then the keys, then the batches against the sample. This guide walks the purchasing and security team through the process step by step and shows what to record as audit evidence.

12
steps of the device trust procedure
Source: card
3
supply chain risks: functionality, firmware, batches
Source: card

Why verify a wristband that only transmits

In a typical concept a BLE wristband only transmits, is charged once a year, has an alarm for photo or strap cut, and has an SOS button, so it seems a simple device. Even so, at a critical site it needs the same attention as a server: every employee wears one, and its signal reaches antennas in the OT network.

Three supply chain risks

The device trust procedure for a BLE wristband has 12 steps and answers three risks: unintended functionality in the circuit, unauthorised firmware, and batches that do not match the sample. Each step checks one of them, and the result goes into the protocol.

Questions from the critical infrastructure operator

The operator asks about the origin of the electronics, who holds the firmware keys, whether the wristband lasts without daily charging and where the servers run. The purchasing team should have an answer to each in the documentation before security asks.

Step by step: from the inquiry to admission to the site

The order below groups the 12 steps of the procedure into four stages. Each stage states who leads it and what stays in the documentation.

Stage 1: documents and origin

The purchasing team collects from the supplier a description of the origin of the electronics, a list of components and the manufacturer's declaration. The documents state what should be in the wristband, and the later stages check whether it actually is.

Stage 2: X-ray inspection of samples

Wristband samples are X-rayed, which shows the contents of the board and housing. The aim is to detect circuits or components outside the list, that is, unintended functionality. Photos and conclusions go into the protocol.

Stage 3: firmware and keys

Firmware control checks that the software in the wristband is the one the supplier declared, and key control checks who generates the keys and where they are stored. At energy facilities the client may require frames signed with its own keys, so this stage settles who has real control over the device.

Stage 4: batches and acceptance

Each delivered batch is compared with the sample approved in stages 2 and 3. A batch that does not match the sample does not enter the site, and the rejection is recorded in the acceptance protocol together with the batch number.

Split of the 12 procedure steps into stages (sample calculation)

Split of the 12 procedure steps into stages (sample calculation)Donut chart: 12 procedure steps split illustratively into four stages of three steps.Documents and origin: 3 steps (25%)X-ray of samples: 3 steps (25%)Firmware and keys: 3 steps (25%)Batches and acceptance: 3 steps (25%)12stepsDocuments and origin3 steps (25%)X-ray of samples3 steps (25%)Firmware and keys3 steps (25%)Batches and acceptance3 steps (25%)
Source: Sample calculation: even split of 12 steps into four stages, for illustration

Where it fits in the network architecture

Wristband verification does not end at the device. The system's architecture in the OT network is presented in the PERA model, with levels 0-6 and DMZ 3.5: the OT network separated by firewalls, no hosts with interfaces in two levels, separate VLANs for management, backup and monitoring, logs to a SIEM, and VPN access with 2FA and a jump host in the OT DMZ.

In the location concept for a large energy site, wristband data left only through the main antennas to the OT VLAN and servers in the OT network. A team that verified the wristband but did not check this data flow leaves a gap on the network side.

Audit evidence: what to record

The auditor will ask how one knows that the wristband on an employee's arm is the one that was approved. The documentation should allow an answer without talking to the author of the procedure. The list below gives the minimum that covers the three supply chain risks.

  • description of the origin of the electronics and a component list from the supplier
  • X-ray inspection protocol for samples, with photos and conclusions
  • firmware control result and an indication of who holds the keys
  • comparison of each batch with the approved sample
  • record of who signed the admission to the site and when

The most common mistakes of purchasing teams

The most common mistake is treating the wristband as a gadget and ordering it without a procedure, because it costs less than a single camera. The second is a one-off check of a sample with no check of later batches. The third is having no answer to the question about keys before acceptance.

Checklist

Video

Frequently asked questions

How many steps does the device trust procedure for a BLE wristband have?

Twelve. It answers three supply chain risks: unintended functionality, unauthorised firmware and batches that do not match the sample.

Is checking one wristband sample enough?

No. Each delivered batch is compared with the approved sample, because the risk is precisely a batch that does not match the sample.

Who should hold the keys for the wristband firmware?

The critical infrastructure operator asks this, and the client may require frames signed with its own keys. The answer is settled before the order.

Does the wristband need daily charging?

In the described concept the wristband only transmits and is charged once a year. Battery life without daily charging comes up in operator questions and needs confirming for the specific model.

Let's prepare the procedure for your purchasing

We will provide the documentation of the device trust procedure and go through it with your purchasing and security team. Tell us when to arrange the talk.

Let's talk