InnerWeb
Skip to main content

Tanker and supplier traffic checklist before gate start

The tanker traffic checklist covers three things the gate coordinator should check before starting: appointment data, driver locators and the delivery route. Each point has a reason that follows from how the system works, so the list is not a generality. Going through it takes a few minutes and prevents typical problems on the first day.

5%
locator battery level below which recharging is recommended
Source: spec sheet
> 1 min
stop threshold marked on the delivery route
Source: spec sheet

Block 1: appointment data

If the plant has a delivery appointment system, it can be connected to InnerWeb via SOAP. After the appointment card code is scanned, the system fetches the delivery data and pre-fills the gate, dock and carrier form. Before starting, the coordinator checks that the connection returns data for several test codes, not only that it works technically.

Two behaviours of the system must also be known. When the data contains no carrier, the form inserts a substitute value so that entry can be registered. A transport with a completed status is deliberately treated as no data, because the appointment system can return the last completed transport for many non-matching codes, and showing it would mean confusing the driver.

Block 2: driver locators

The service tab for driver locators is read-only. Devices that are offline or have a battery down to 5 percent receive the recommendation 'Recharge and switch on'. Before starting, the coordinator reviews the tab and recharges the devices, because a driver with a non-working locator is invisible on the map.

It is also worth checking how many locators are in circulation compared with the number of planned deliveries. A spare stock allows the units that came back with a low battery to be swapped out.

Split of checklist points by block

Split of checklist points by blockPie chart: three points on appointment data, three on locators, three on route and stages, two on recording and reports.Appointment data: 3 points (27.3%)Driver locators: 3 points (27.3%)Route and stages: 3 points (27.3%)Recording and reports: 2 points (18.2%)11pointsAppointment data3 points (27.3%)Driver locators3 points (27.3%)Route and stages3 points (27.3%)Recording and reports2 points (18.2%)
Source: Count of checklist points on this page; the figures count points, not measurements

Block 3: delivery route and stages

The delivery route view isolates one active delivery and shows the locator route from the entry, stops longer than one minute and the pin of the declared destination. Before starting, the coordinator makes a test drive with a locator and checks whether the route is readable on all road sections.

For delivery stages, for example the gate, the weighbridge and the warehouse, a standard time is set. The stage time alarm rings the phone when a stage exceeds that time. A time that is too short generates false alarms, and one that is too long misses problems, so the values are chosen after several days of measurement.

Block 4: recording and reporting

Every reading of an appointment card code is saved with its result, response time and operator. In this way recurring reports of non-working cards can be confirmed or refuted with numbers. Before starting, the coordinator checks that the recording works and who has access to the report.

The full delivery run, that is routes and times per warehouse, goes into the reports. After the first week it is worth reviewing them and deciding which stages need a correction of thresholds or a conversation with the carrier.

What the checklist does not replace

The list covers data and devices, not regulations. Procedures for entering the depot, requirements for drivers and Ex zones are set by the plant in its own documents. The system provides visibility and recording, but does not replace the gate instructions or the driver training.

Checklist

Video

Frequently asked questions

What to do when the appointment has no carrier?

The delivery form inserts a substitute value, so the entry can be registered; the data is completed later.

Why does the system not show data for a code with a completed transport?

A completed transport is treated as no data, so the driver is not confused with the previous delivery.

How to check which locators need charging?

In the service tab, which shows devices that are offline or have a battery down to 5 percent.

How to set the stage times?

From several days of measurements in the reports, followed by a correction of the stage time alarm threshold.

Start the gate with a ready checklist

Book a call with InnerWeb and match the checklist to the appointments, the locators and the delivery stages at your depot.

Let's talk