InnerWeb
Skip to main content

Choosing radio beacons for cold storage and freezers

A refrigerated chamber is an environment where battery transmitters must be selected more carefully than in a heated hall. Before ordering, the head of logistics should check several points that decide whether the network will run stably for years.

100-200 m²
floor area per transmitter in a building
Source: project card
15-30
transmitters for a 3,000 m² chamber
Source: sample calculation

Who these recommendations are for

The recommendations are for logistics and maintenance managers in warehouses with cooled chambers and freezers, where employees move on foot or by pallet truck and the plant wants to know their location for safety and workflow.

We do not give battery temperature parameters or operating ranges here, because the values depend on the cell used and must come from its specification. We follow the rule that battery life is not promised as a guarantee, and in a cold chamber this applies even more.

Recommendations 1 and 2: temperature requirements and power calibration

First, record the actual temperatures of the chambers, including fluctuations when doors are opened and during defrosting, and pass them to the supplier before the offer. It is a generally known fact that cell capacity drops with temperature, so the battery replacement plan in a cold chamber should be more cautious than in a heated hall.

Second, require power calibration of the transmission to the chamber. Power calibration reduces crosstalk and extends battery operation, and battery life is planned after calibration, not according to factory settings. In a chamber with racks and goods of high humidity, power set too high increases consumption and crosstalk between neighbouring rooms.

Number of transmitters for a chamber (recommendation of 100-200 m² per unit)

Number of transmitters for a chamber (recommendation of 100-200 m² per unit)Bar chart: number of transmitters for chambers of 1,000, 3,000 and 5,000 m² at a density of 1 per 100 m² and 1 per 200 m².01020304050units1 per 100 m² (1,000 m²): 10 units10 units1 per 200 m² (1,000 m²): 5 units5 units1,000 m²1 per 100 m² (3,000 m²): 30 units30 units1 per 200 m² (3,000 m²): 15 units15 units3,000 m²1 per 100 m² (5,000 m²): 50 units50 units1 per 200 m² (5,000 m²): 25 units25 units5,000 m²
  • 1 per 100 m²
  • 1 per 200 m²
Source: Sample calculation based on the assumptions in the page text; not an offer, individual quotation applies.

Recommendations 3 and 4: density and position from several transmitters

Take 1 transmitter per 100-200 m² in a building as the starting point and correct it after a test walk. The position results from the signals of several transmitters averaged on the map, not from the strongest one, so in a chamber every point where location is needed should see several transmitters.

Pay attention to the walls and doors of the chambers. Insulated walls, racks with goods and doors can attenuate the signal, so treat neighbouring chambers as separate coverage zones and check the position on the zone boundaries. Location works without GPS, which is an advantage in a closed warehouse, but it does not replace a coverage plan.

Recommendations 5 and 6: installation and servicing in the chamber

Battery power means installation without intervening in the electrical installation: there are no cables through the chamber walls and no penetrations that have to be sealed. This is a real benefit in a chamber, where every penetration is a potential thermal bridge.

Plan servicing so that it does not require a long stay in the freezer chamber. Battery replacement is part of the maintenance service, with monitoring of correct operation and support. For a freezer it is worth agreeing with the supplier on shorter work windows and on early indication of the transmitters to be replaced, based on monitoring.

Recommendation 7: questions for the supplier and a sample calculation

Ask the supplier which cells are used and what their temperature ranges are, how the power calibration procedure in the chamber works, how the battery status is reported, and what the replacement plan is. Ask for written answers, not general declarations.

A sample calculation of the number of units: for a chamber of 1,000, 3,000 or 5,000 m², the recommendation of 1 transmitter per 100-200 m² gives respectively 5-10, 15-30 and 25-50 units. This is the starting point for a quotation, not the final design: the number is corrected by the test walk and the required accuracy.

Example calculation

Number of transmitters for a cooled chamber

Assumptions
ParameterValue
Chamber area3,000 m²
Recommended density100-200 m² per transmitter

Result: 15-30 transmitters as the starting point for the quotation

Note: Sample calculation based on the assumptions in the page text; not an offer, individual quotation applies.

Checklist

Video

Frequently asked questions

Do radio beacons work in a cold storage chamber?

The temperature range depends on the cell used and must follow from its specification. Before ordering, the actual chamber temperatures should be passed to the supplier and a written answer obtained.

Is battery operation time in freezing conditions guaranteed?

No. Battery operation time is not given as a guarantee. It is planned after power calibration and verified by monitoring the network status.

How many transmitters does a 3,000 m² chamber need?

According to the recommendation of 1 transmitter per 100-200 m², 15-30 units is the starting point. The final number is set by the test walk and the required accuracy.

Let us review the network plan for cooled chambers

We will go through the chamber temperatures, power calibration and the battery replacement plan with you. The quotation is individual.

Let's talk