InnerWeb
Skip to main content

Good practice: service visit to a site without staff

A technician travels alone to a site where nobody will greet him and nobody will notice if something goes wrong. The service planner therefore has one task before the trip: make sure the permit, the watch and the response procedure are ready before the person enters the grounds. Below are the practices, arranged in planning order.

20 s
warning after no movement
Source: production deployment (card)
7 z 10
stops cancelled by the worker alone
Source: production reference (card)
3 400 h
watch time in the production reference
Source: production reference (card)

Why a trip to a site without staff is different

At a site with staff, someone knows the technician has arrived, someone opens the gate and notices when he disappears from view. At an unattended site this net does not exist. The only net is what the planner prepares before the trip. The duty to ensure safe working conditions results from Article 207 of the Labour Code, and the system provides evidence for an audit, not a guarantee of compliance.

The worker's position serves three purposes in the system: a view of who is on site, automatic joining and leaving of the work permit, and the worker safety function. A good trip preparation uses all three.

Practice 1: permit ready before entering the grounds

The work permit should be issued before the technician reaches the site. Because the position from pulses makes it possible to join the worker to the permit automatically after entering the site and to close his participation after leaving, the planner does not need to remember manual entries on site. The scope of work, the place and the responsible person are recorded in advance, and presence is confirmed in the background.

Time thresholds the technician should know

Time thresholds the technician should knowBar chart: SOS countdown 3 seconds, no-movement warning 20 seconds, no-movement alarm 50 seconds.01020304050sSOS countdown: 3 s3 sSOS countdownNo-movement warning: 20 s20 sNo-movement warningNo-movement alarm: 50 s50 sNo-movement alarm
Source: Product documentation and parameters of a working production deployment; alarm = 20 s + 30 s

Practice 2: watch checked before the trip

The watch is the technician's only alarm channel. The planner checks three things: that the device is assigned to this person, that the battery level is sufficient, and that the last pulse reached the platform. The watch sends a pulse periodically with information about the transmitters it hears, signal strength, battery level and status, so this data is visible even before the trip.

Details on charging and the spare watch are described in separate good practices for mobile crews.

Practice 3: response procedure set in advance

The SOS on the watch is triggered by a triple press or by holding the button, with a 3-second countdown that allows cancellation. In a working production deployment the no-movement alarm warns after 20 s without movement, and after a further 30 s without a response it raises an alarm; an automatic dialer calls the designated people and repeats until someone answers. Before the technician leaves, the planner should know who will take the alarm and who is the nearest person able to reach the site.

Naming the people to notify is part of the trip plan, not something decided only after an alarm.

Practice 4: the technician knows the rules before the gate

Before entering, the technician should know how the SOS works, what the no-movement warning means and how to cancel it. In a production reference covering over 3,400 hours of watch time, 7 out of 10 stops were cancelled by the worker himself, and the median time to close an alarm on site was 52 s. Good knowledge of the rules means fewer false escalations.

Practice 5: check the record after the trip

After the work ends, the planner reviews the record: whether the technician entered and left according to plan, whether the permit was closed and whether any alarms appeared. After an event the system generates a report with the time, the location and the course of the escalation, which can be attached to the site documentation.

Checklist

Video

Frequently asked questions

Does the technician need to join the permit manually on site?

No. The position from pulses is used to join and release the worker automatically, so presence is confirmed in the background.

When should the watch be checked?

Before the trip, because the watch is the technician's only alarm channel. The last pulse and the battery level can be seen on the platform.

Are these practices enough to meet the requirements?

The system supports meeting the requirement and provides evidence for an audit. The basis of the duty is Article 207 of the Labour Code.

Sources

Let us prepare service trips without surprises

We will show how the permit, the watch and the response procedure come together as one trip plan for your sites.

Let's talk