How the system counts entries and exits
The security panel has no separate entry and exit buttons. The first scan of a compliant employee records an entry, and the second an exit. This rule is convenient at the gate, but it has an obvious weakness: if an employee leaves the plant without a scan, the system considers them still present.
The effect is practical. The list of people on site shows someone who is not on the plant, and during an alarm or evacuation the list stops being reliable. That is why we treat a forgotten exit as a phenomenon to handle in the system, not only to remind employees about.
When the system checks out automatically
A person who forgot to scan their exit is checked out automatically once they have been on site for longer than 12 hours. The verification task runs every 3 hours, so the actual check-out happens in the first run after the threshold is exceeded.
This gives security a simple calculation. A person who entered at 6:00 and did not scan an exit will exceed 12 hours at 18:00. If the task runs at fixed intervals every 3 hours, the check-out happens within the next 3 hours at the latest, that is by 21:00 in this example. During that time the person may still appear on the list, so the list should not be the only source during an incident.
Is 12 hours a good threshold for 12-hour shifts?
The threshold is set above a typical shift, so a person working longer than a standard day is checked out only after exceeding 12 hours. A plant with extended shifts should be aware of this and agree with the agency who checks the list at shift handover.
Time thresholds in exit handling
What security sees
Security sees the list of people on site as one of five panel views. After an automatic check-out the person disappears from the list, and the log keeps the entry without a manually recorded exit. This makes it possible afterwards to tell a scanned exit from a check-out performed by the system.
Denials behave differently. A scan with a negative verdict records a denial entry, and the person with a denial is not counted as present on site. A forgotten exit therefore concerns only people who actually entered.
- Entry recorded by scan, no exit scan: the person stays on the list until automatic check-out.
- More than 12 hours: the person is checked out in the next run of the task.
- Denial: entry in the log, the person is not on the list of people on site.
- Duplicate scan within a few seconds: ignored with a message, no new entry.
A tap after a group training is not an exit
A special case concerns group trainings at the registration workstation. A card tap made up to 13 minutes after completing a group training is not counted as an exit; it only confirms presence. Without this rule a participant who tapped their card right after the test would be recorded as leaving, although they are inside.
For security this is important information: a short gap between the training and the tap is not an error of the employee or the system. If the employee scans again after 13 minutes, that tap is already a normal scan.
When to correct the entry by hand
Automation tidies the list but does not replace a human decision. A manual correction is needed when the list of people on site must be reliable earlier than after 12 hours, for example before an evacuation drill, when the plant closes or after an incident on the site.
In that case the shift leader compares the list with actual presence, establishes who left without a scan, and records the explanation in the shift report. It is worth agreeing with the agency a fixed moment for such a review, for example at shift handover.
How to limit forgotten exits
The cheapest measure is an exit workstation visible to the employee and a clear sign at the gate saying that leaving also requires a scan. The second measure is reviewing the report of people checked out automatically once a week: if the same people return to the list after 12 hours, talk to them or improve the exit arrangements.
The third measure is a division of responsibility written into the agreement with the agency: who checks the list, at what time and what they do when the numbers do not match.
Video
Frequently asked questions
Does automatic check-out delete the entry from the log?
No. The entry stays in the log and the person disappears from the list of people on site. This makes it possible later to tell a scanned exit from a check-out performed by the system.
Can a person checked out automatically enter again straight away?
Yes, as long as they meet the verdict requirements. A new scan is treated as another entry, because the person is no longer on the list as present.
Can the 12-hour threshold be treated as the exact time of exit?
No. The automatic check-out is an administrative record, not proof of the exit time. Only an exit scan records the exact time.
Are a duplicate scan and a forgotten exit the same problem?
No. A duplicate is a repeated scan of the same code within a few seconds and is ignored with a message. A forgotten exit means there is no second scan at all.
Let us check the people-on-site list on your data
During the demo we will show the log of entries, exits and automatic check-outs and agree with your security team the moment of a manual list review.
Let's talk