Who these recommendations are for
The recommendations are for the purchasing department, which selects the scanner model, and for IT, which prepares the guard post. They concern the station where the guard scans QR badges in the security panel running in a browser. InnerWeb is a software maker, not a device maker: scanners are bought from hardware suppliers, and the software works with them in two modes described below.
We do not give the model or the price of a specific device. The recommendations describe the features to agree before purchase and the settings to check after installation.
Seven recommendations
Each recommendation has a justification based on how the security panel behaves and on typical scanner settings.
1. Choose USB HID by default
In this mode the scanner works like a keyboard, so it needs no drivers and no browser permission to access a port. The panel tells it from a human by a character gap below 34 ms, and clears an unfinished read after 233 ms. This is the simplest route to starting the station and a good baseline for the first tests.
2. Keep USB-COM for situations where HID is not enough
USB-COM mode works through Web Serial in the Chrome and Edge browsers. It is useful when the keyboard layout causes problems or when the station uses several scanners. It has its specifics: the scanner may appear as two ports of the same device, so the panel opens all ports of the device and removes duplicates within a 2584 ms window.
3. Agree the keyboard layout of the scanner and the system
In HID mode the scanner sends key codes, which the system turns into characters. A wrong layout or Caps Lock distorts the address. The panel parser tries a second time with the reversed mapping, but this is a safeguard, not a replacement for correct configuration.
4. Enable reading of codes containing a web address
On scanners from some manufacturers, reading of QR codes containing a web address is disabled by default, and the scanner sends nothing at all. This option must be explicitly enabled. No reaction from the scanner to the first badge is most often exactly this case, not a failure.
5. Repeat the test after every change of interface
A change of scanner interface, for example from USB HID to USB-COM, restores the default symbol settings. After such a change the reading of addresses and the keyboard country code must be checked again. Recording this requirement in the start-up instructions saves repeated reports.
6. Program the scanner with the cable connected throughout the sequence
Programming the scanner with configuration codes requires the USB cable to stay connected for the whole sequence. A loss of power during it discards the settings being changed, and the scanner may remain in its previous configuration with no visible error signal. After programming, perform a test scan.
7. Plan a second unit and write down the configuration
The scanner is most often the element replaced at a station. A second, pre-configured unit kept in a drawer shortens downtime to the time needed to swap the cable. Written-down settings (mode, layout, reading of addresses) let you do the same without the knowledge gained at the first start-up.
Timing thresholds for scanner handling in the panel
How to check the station before the first change
The acceptance test takes a dozen or so minutes and should cover a badge with a correct code, a badge with a code that does not exist, and a double scan. A double scan of the same code within 5 seconds is ignored on the server side, so the guard sees an informational message instead of a new entry. The panel does not treat the code from the badge as an address to open or as a command, and its length is limited, so a test with a foreign code is safe.
It is worth adding to the test a situation in which the guard checks a person manually because the code does not work. The gate screen allows searching for a company from 2 characters and shows its employees with a column for today's permit, so manual verification is a backup, not a reason to stop traffic.
What we do not recommend
We do not recommend buying a scanner based on price alone, without checking whether its modes and settings can be set using configuration codes. We also do not recommend changing the operating mode during a shift, because the symbol settings then return to defaults and the scanner stops reading addresses. Carry out hardware changes outside peak hours and always scan a test badge afterwards.
Video
Frequently asked questions
Which scanner mode is simpler to start?
USB HID, because the scanner works like a keyboard and needs no browser permission to access a port. USB-COM requires the Chrome or Edge browser.
Why are there two ports visible in USB-COM mode?
The scanner may appear as two ports of the same device. The panel opens all ports of the device and removes duplicates within a 2584 ms window.
Does InnerWeb supply the scanners?
No. InnerWeb is a software maker, and the scanner is bought from a hardware supplier. The software works with scanners in USB HID and USB-COM mode.
Setting up a new reception?
We will go through the choice of scanner mode, the configuration and the acceptance test with your IT team, so that the first change does not start with a diagnosis.
Let's talk