What the uncertain tab is and why it exists
The evacuation list is generated from current data on people's presence on site and divides people into six groups. Five of them correspond to categories of people present, and the sixth is a separate tab for people whose attendance status is uncertain. It shows those whom the register still considers present, but for whom the data raises doubts.
The design principle is clear: an error in one direction costs less than an error in the other. A person listed who has already left means unnecessary searching. A person missing from the list is someone nobody looks for. That is why the system shows rather too many people than too few, and gathers doubtful ones in one tab instead of removing them.
Three reasons someone ends up as uncertain
The health and safety manager should know the reasons, because they determine how the person is settled. The list shows the reason next to each person, which shortens the conversation with the marshal at the assembly point.
The first reason is an entry without an exit scan that is older than 12 hours and that the scheduled task has not yet closed. The second is a person who was on site, scanned the code at the gate and received a refusal. The third is induction training at a workstation without a completion signal: the person scanned the code at the workstation, started the training, and after 3 to 6 hours there is no end signal.
- An old entry without an exit scan, older than 12 hours.
- A refusal at the gate of a person who was on site.
- Induction training at a workstation without a completion signal.
Uncertain people and the time to settle them in a drill
Practice 1: rehearse separate settlement of the uncertain
In the drill scenario, plan a place and a person who is responsible only for the uncertain tab. The other groups are settled according to the usual scheme at the assembly points, while the uncertain require phone calls, contact with the external company's host and a check whether the person really left the site.
A printout of the list creates one page for each group, so the commander can hand the sheets to different coordinators. For the uncertain tab it is worth naming a permanent coordinator who is not at the same time the marshal of any other group.
Practice 2: set the order of settlement
Not all uncertain people carry the same weight. Check first the people with a refusal at the gate, because their last event is the most recent and they may still be on site. Then the people from workstation training, because a workstation has a specific place where they can be found. Last come the old entries without an exit scan, which are often a forgotten tap.
Write this order into the drill instructions and check it in at least one drill a year.
Refreshing the list during settlement
The list refreshes every 13 seconds, so during a drill the data may change, for example after a late exit tap. For a printout the time of its generation applies. The coordinator should keep this in mind and note the hour.
Practice 3: record the settlement result
The drill makes sense if afterwards you can state how many people from the uncertain tab were found, in what time and for what reason. Prepare a simple protocol sheet: the number of people in the tab at the start, the number settled at minutes 5, 10 and 15, and the number not settled after the end.
The entry and exit register on which the list is based is material for the plant audit. The drill protocol is attached to it, so that after a year it is visible whether the number of uncertain people is falling.
Practice 4: reduce the number of uncertain at the source
The best way to settle the uncertain is to have fewer of them. Inform the employees of external companies that every exit must be scanned. The completion of training at a workstation should be clearly confirmed. A refusal at the gate of a person who is on site must be explained on the spot, and not left for the tab.
In a sample calculation for a plant with 180 people on site and 5% uncertain, settling 9 people takes the coordinator about 30 minutes. After training contractors on the rule of scanning the exit, and the drop of uncertain to 2%, there are 4 people and about 13 minutes. These are assumptions for your own measurement, not a result from a specific plant.
Settling the uncertain tab in a drill
| Parameter | Value |
|---|---|
| People on site | 180 people |
| Uncertain before actions | 5 % |
| Uncertain after actions | 2 % |
| Settlement time per person | 3.3 min |
Result: 9 people and about 30 min versus 4 people and about 13 min
Note: Sample calculation; the settlement time per person depends on the plant's organization.
Checklist
Video
Frequently asked questions
Is a person in the uncertain tab definitely on site?
No. The register considers them present, but the data raises doubts. The list shows rather too many people than too few.
Do uncertain people count toward the total on site?
No. The total covers only the five groups of people present, and the uncertain are shown separately.
How often does the list refresh?
Every 13 seconds on screen. A printout reflects the state at the time of generation.
What about people who left and forgot to scan the exit?
They remain as present or uncertain until the entry is closed, and after the stay threshold is exceeded a scheduled task closes them.
Test the evacuation list
We will show the uncertain tab on sample data and help you prepare a drill scenario. Book a conversation with the InnerWeb team.
Let's talk